Mac CNC Machine Tool Repair
Independent Contractor
Page3
Jimmie L. Odom
3072 Dogwood Lake Road
Bailey, MS 39320
Phone: 601-681-8001 Fax: 601-681-9694
E-mail: jim@flex-o.com
Machine Tools Specification for Sales
1. Brand: Enco Gap Bed Engine Lathe 20" X 80" "Iron Flower"
2. Year: 1985
3. Control:
4. Options:
5. Hours:
6. Number Shifts: 1
7. Price: $ 7,000.00
8. Available: Immediate
9. Material Cut: Alum. 75% Plastic / Steel
10. Equipment ran in an in house shop manufacturing own product.
11. Machine Specifications: Model IF-510
Center Height 10"
Swing Over Bed 20"
Swing Over Gap 27"
Swing Over Cross Slide 13"
Distance Between Centers 80"
Type of Spindle Nose D1-8
Spindle Bore 3 1/8"
Taper of Spindle ASA No. 350
Spindle Speeds 12 Steps (30-1800 RPM)
Cross Slide Travel 10 1/4"
Compound Rest Travel 5"
Tailstock Spindle Dia. 2 1/4" Dia.
Tailstock Spindle Travel 6"
Taper of Tailstock Center M.T. No. 4
Bed Length 96"
Bed Width 13"
Width of Gap 12 1/2"
Leadscrew 4 TPI
Metric Pitch Threads 0.5-7 mm/pitch (22 kinds)
Inch Threads 4-56 TPI (36 kinds)
Module Pitch Threads 0.25-3.5M (20 kinds)
D P Threads 8-112P. (34 kinds)
Range of Longitudinal Feeds 0.06-0.88mm/rev.
Motor 7 1/2 HP 440v
Approx. Weight 2400 lbs.
NOTES: This equipment was purchased NEW and has all manuals. Equipment has run on one shift only. This machine has had motor reworked and runs on 440v. Machine has never been crashed. This equipment is in very good condition and holds tolerance very very good. The following is tooling that goes with equipment.
1. One 3 jaw 10" Chuck
2. One 4 jaw 10" Chuck
3. One 6 jaw 10 Chuck
4. One Steady Rest
5. One Follower Rest
6. Anilam Numerical Read Out
7. Delorian Quick Change Tool Holders With Tools
8. Assorted Tools
9. One Slotted Face Plate
10. Versa Mill with Milling and Grinding attachments
Jimmie L. Odom
3072 Dogwood Lake Road
Bailey, MS 39320
Phone: 601-681-8001 Fax: 601-681-9694
E-mail: jim@flex-o.com
Machine Tools Specification for Sales
1. Brand: Enco Vertical Turret Milling Machine
2. Year: 1985
3. Control:
4. Options: Power Draw Bar
5. Hours:
6. Number Shifts: 1
7. Price: $ 5,000.00
8. Available: Immediate
9. Material Cut: Alum. 90% Plastic / Steel
10. Equipment ran in an in house shop manufacturing own product.
11. Machine Specifications:
Table Size 10" X 54"
Table Travel 31"
Cross Travel 16"
Ram Travel 18"
Knee Travel 16"
Quill Travel 5"
Quill Power Feed Rate .015, .03, .06, Rev.
Vertical Spindle Taper R-8
Spindle Motor 3 HP 440v
Vertical Spindle
Speed-rpm Vari-speed 70-4000
Overall Height 86"
Overall Depth 85"
Weight 2750 Lbs.
Notes: This equipment was purchased NEW and has all manuals. Equipment has run on one shift. Machine has never been crashed. This equipment is in very good condition. The following is tooling that goes with equipment. This machine equipped with a power draw bar, Lyman Mk-7 power feed on table; power cross feed; Anilam numerical readouts on X and Y; Super spacer, rotary table; index head; one set of R-8 Collets; lots of assorted end mills and drill chucks; Tap-Matic taping head Boaring and Facing mills (3); there is lots of carbide tooling with the equipment.
Next Page